superfinishing

Case Study of ISO TS 6336-22 Micropitting Calculation

Case Study of ISO/TS 6336-22 Micropitting Calculation

Posted by on Wednesday, May 5th, 2021 in

ISO/TS 6336-22 (Calculation of load capacity of spur and helical gears — Part 22: Calculation of micropitting load capacity) is the ISO technical specification containing a proposal for a calculation for the risk of micropitting in gear sets....

View More
The History of Electroplating and a Historical Review of the Evolution of NASF

The History of Electroplating and a Historical Review of the Evolution of NASF

Posted by on Monday, April 5th, 2021 in

The history of electroplating is a curious mixture of mistakes, observations, serendipity and experimental development, enmeshed and entwined with the discovery of electricity in the late 18th century....

View More
mass media finish-BV-Products

Mechanical Paste Polishing vs. CAVF Finishing of Gears

Posted by on Monday, August 3rd, 2020 in

A recent Materials Matter article compared generic deburring versus CAVF (chemically accelerated vibratory finishing.) Both techniques are conducted in a vibratory unit....

View More
Senjo Gear1 before

The Challenges of Generic Deburring vs. CAVF Deburring

Posted by on Sunday, July 19th, 2020 in

Relative to gear hobbing, shaving, and/or post heat-treat grinding to generate accurate tooth morphology there may come a time wherein vibratory deburring is a requirement to remove adherent burrs. ...

View More
Lattice-Bracelet

Metal Finishing for 3D Printed Parts Webinar – Part 8 – LATTICE BRACELET

Posted by on Tuesday, July 7th, 2020 in

Metal Finishing for 3D Printed Parts While many can be put into operation as sintered, there are a number of […]...

View More
Open-Impeller

Metal Finishing for 3D Printed Parts Webinar – Part 7 – OPEN IMPELLER

Posted by on Monday, July 6th, 2020 in

Metal Finishing for 3D Printed Parts While many can be put into operation as sintered, there are a number of […]...

View More
Finger-Spints

Metal Finishing for 3D Printed Parts Webinar – Part 5 – FINGER SPLINTS

Posted by on Monday, July 6th, 2020 in

Metal Finishing for 3D Printed Parts While many can be put into operation as sintered, there are a number of […]...

View More
Parachute-Rings

Metal Finishing for 3D Printed Parts Webinar – Part 4 – PARACHUTE RINGS

Posted by on Monday, July 6th, 2020 in

Metal Finishing for 3D Printed Parts While many can be put into operation as sintered, there are a number of […]...

View More
GEARS

Metal Finishing for 3D Parts Webinar – Part 3 – GEARS

Posted by on Monday, July 6th, 2020 in

Metal Finishing for 3D Printed Parts While many can be put into operation as sintered, there are a number of […]...

View More
Shock-Absorber

Metal Finishing for 3D Printed Parts Webinar – Part 6 – SHOCK ABSORBER PISTON

Posted by on Monday, July 6th, 2020 in

Metal Finishing for 3D Printed Parts While many can be put into operation as sintered, there are a number of […]...

View More
MM Roughness Measurement

Materials Matter : Roughness Measurement: Optical vs. Contact Stylus Profilometry

Posted by on Sunday, April 19th, 2020 in

Optical profilometry will become an important tool for predicting gear performance with more research and development of an objective lens to fit into tooth spaces....

View More
Report of the Condition of a General Electric Transportation Systems Gearbox

Report of the Condition of a General Electric Transportation Systems Gearbox

Posted by on Tuesday, April 14th, 2020 in

Wind power plant operation and maintenance (O&M) costs remain an appreciable contributor to the overall cost of wind energy, with a capacity-weighted average of $11/megawatt-hour (MWh) for projects installed since 2000 and $9/MWh for projects install...

View More